After a power failure, our Out-of-Warranty MD3000i is not working properly. I think that both controllers are having problems. I can ping both management IPs, and vmkping at least 1 or the 4 iSCSI IPs. If I connect with only 1 ESXI server, I am able to connect the the lun to get the data off.... but very slowly. eg 16GB took 4 days.
2 weeks before power outage, I changed the MD3000i iSCSI ports to use jumbo frames. This was working properly until the power outage.
I can get to the MDSM, but I am not able to reach iSCSI > Configure iSCSI Host Ports. I can click section, but it will not launch the iSCSI Host Ports configuration page. I want to try and disable jumbo frames.
Questions:
Is there a way to just use 1 controller until I get a replacement?
What is the problem with controller 0? , Can it be fixed? , Is it related to the jumbo frames setting, and can it be disabled from serial?
#--- Controller 0 Serial Output BEGIN -------------------------------------------------
-=<###>=-
Attaching interface lo0... done
Adding 9768 symbols for standalone.
Error
03/06/16-01:14:24 (GMT) (tRootTask): NOTE: I2C transaction returned 0x0423fe00
WARNING: Reset by alternate controller
Current date: 03/05/16 time: 16:29:45
Send <BREAK> for Service Interface or baud rate change
03/06/16-01:14:41 (GMT) (tRAID): NOTE: SOD Sequence is Normal, 0
03/06/16-01:14:41 (GMT) (tRAID): NOTE: SOD: removed SAS host from index 0
03/06/16-01:14:41 (GMT) (tRAID): NOTE: In iscsiIOQLIscsiInitDq. iscsiIoFstrBase = 0x0
03/06/16-01:14:41 (GMT) (tRAID): NOTE: Turning on tray summary fault LED
03/06/16-01:14:42 (GMT) (tNetCfgInit): NOTE: Network Ready
esmc0: Link change detected, LinkDown may take a long time to detect
03/06/16-01:14:43 (GMT) (tRAID): NOTE: SYMBOL: SYMbolAPI registered.
0x36d600 (tNetTask): esmc0: LinkUp event
03/06/16-01:14:46 (GMT) (tRAID): NOTE: Initiating Drive channel: ioc:0 bringup
03/06/16-01:14:49 (GMT) (tRAID): NOTE: IOC Firmware Version: 00-24-63-00
03/06/16-01:14:58 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:0 phy:0 prevNumActivePhys:2 numActivePhys:2
03/06/16-01:14:58 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:0 phy:1 prevNumActivePhys:2 numActivePhys:2
03/06/16-01:14:59 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:1 phy:2 prevNumActivePhys:2 numActivePhys:2
03/06/16-01:14:59 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:1 phy:3 prevNumActivePhys:2 numActivePhys:2
03/06/16-01:14:59 (GMT) (tSasCfg014): NOTE: Alt Controller path up - chan:0 phy:18 itn:1
03/06/16-01:14:59 (GMT) (tSasCfg021): NOTE: Alt Controller path up - chan:1 phy:16 itn:2
03/06/16-01:15:08 (GMT) (tRAID): NOTE: IonMgr: Drive Interface Enabled
03/06/16-01:15:09 (GMT) (tRAID): NOTE: SOD: Instantiation Phase Complete
03/06/16-01:15:09 (GMT) (tRAID): NOTE: Inter-Controller Communication Channels Opened
03/06/16-01:15:09 (GMT) (tSasDiscCom): NOTE: SAS Discovery complete task spawned
03/06/16-01:15:09 (GMT) (IOSched): NOTE: New Initiator: 1 - channel: 1,devHandle: x27, SAS Address: 5848f694f6e72a00
03/06/16-01:15:09 (GMT) (tRAID): NOTE: LockMgr Role is Slave
03/06/16-01:15:09 (GMT) (sasCheckExpanderSet): NOTE: Expander Firmware Version: 0116-e05c
03/06/16-01:15:09 (GMT) (sasCheckExpanderSet): NOTE: Expander SAS address: Hi = x50026b94 Low = x614f0710
03/06/16-01:15:09 (GMT) (tRAID): NOTE: spmEarlyData: Using cached data
03/06/16-01:15:14 (GMT) (tSasDiscCom): WARN: SAS: Initial Discovery Complete Time: 30 seconds
03/06/16-01:15:14 (GMT) (tRAID): NOTE: WWN baseName 00040026-b9614f07 (valid==>SigMatch)
03/06/16-01:15:14 (GMT) (tRAID): NOTE: ionEnableHostInterfaces is waiting for a channel to become ready
03/06/16-01:15:14 (GMT) (tRAID): NOTE: ionEnableHostInterfaces waited 800ms for a channel to become ready
03/06/16-01:15:14 (GMT) (tRAID): NOTE: IonMgr: Host Interface Enabled
03/06/16-01:15:14 (GMT) (tRAID): NOTE: SOD: Pre-Initialization Phase Complete
03/06/16-01:15:27 (GMT) (tRAID): NOTE: ACS: autoCodeSync(): Process start. Comm Mode: 0, Status: 1
03/06/16-01:15:28 (GMT) (tRAID): NOTE: SOD: Code Synchronization Initialization Phase Complete
03/06/16-01:15:29 (GMT) (NvpsPersistentSyncM): NOTE: NVSRAM Persistent Storage updated successfully
03/06/16-01:15:29 (GMT) (tRAID): NOTE: USM Mgr initialization complete with 0 records.
03/06/16-01:15:29 (GMT) (tRAID): NOTE: EDR - recieved 1 small records
03/06/16-01:15:29 (GMT) (tRAID): NOTE: EDR - recieved 0 large records
03/06/16-01:15:30 (GMT) (tRAID): NOTE: Acquire 0.024 secs
03/06/16-01:15:31 (GMT) (tRAID): NOTE: QLStartFw: Downloading Driver's FW image 03.00.01.47 from 031fb740 4c0c8 bytes , result 0
03/06/16-01:15:58 (GMT) (tRAID): WARN: QLMailboxCommand: Cmd = 0069, completion timeout
03/06/16-01:15:58 (GMT) (tRAID): WARN: QLMailboxCommand: command completion timeout, cmd = 0x69
03/06/16-01:15:59 (GMT) (tRAID): NOTE: Qlogic coredump file written to '9J6GTL1:/tmp/QLogic_Coredump_port_0_9J6GTL1',rc 204E50, expected 204E50
03/06/16-01:15:59 (GMT) (tRAID): WARN: Qlogic coredump file write failed.fclose returned -1
03/06/16-01:15:59 (GMT) (tRAID): NOTE: QLProcessSystemError: Restart RISC
03/06/16-01:15:59 (GMT) (tRAID): ERROR: QLGetFwState: MBOX_CMD_GET_FW_STATE failed. Stat f000
03/06/16-01:15:59 (GMT) (tRAID): NOTE: QLRebootTimer: Status after Get FW State 4543
03/06/16-01:15:59 (GMT) (tRAID): NOTE: QLRebootTimer: QLGetFwState failed
03/06/16-01:16:01 (GMT) (tRAID): NOTE: QLStartFw: Downloading Driver's FW image 03.00.01.47 from 031fb740 4c0c8 bytes , result 0
03/06/16-01:16:28 (GMT) (tRAID): WARN: QLMailboxCommand: Cmd = 0069, completion timeout
03/06/16-01:16:28 (GMT) (tRAID): WARN: QLMailboxCommand: command completion timeout, cmd = 0x69
03/06/16-01:16:29 (GMT) (tRAID): NOTE: Qlogic coredump file written to '9J6GTL1:/tmp/QLogic_Coredump_port_0_9J6GTL1',rc 204E50, expected 204E50
03/06/16-01:16:29 (GMT) (tRAID): WARN: Qlogic coredump file write failed.fclose returned -1
03/06/16-01:16:29 (GMT) (tRAID): NOTE: QLProcessSystemError: Restart RISC
03/06/16-01:16:29 (GMT) (tRAID): ERROR: QLGetFwState: MBOX_CMD_GET_FW_STATE failed. Stat f000
03/06/16-01:16:29 (GMT) (tRAID): NOTE: QLRebootTimer: Status after Get FW State 4543
03/06/16-01:16:29 (GMT) (tRAID): NOTE: QLRebootTimer: QLGetFwState failed
03/06/16-01:16:30 (GMT) (tRAID): NOTE: QLStartFw: Downloading Driver's FW image 03.00.01.47 from 031fb740 4c0c8 bytes , result 0
03/06/16-01:16:57 (GMT) (tRAID): WARN: QLMailboxCommand: Cmd = 0069, completion timeout
03/06/16-01:16:57 (GMT) (tRAID): WARN: QLMailboxCommand: command completion timeout, cmd = 0x69
03/06/16-01:16:58 (GMT) (tRAID): NOTE: Qlogic coredump file written to '9J6GTL1:/tmp/QLogic_Coredump_port_0_9J6GTL1',rc 204E50, expected 204E50
03/06/16-01:16:58 (GMT) (tRAID): WARN: Qlogic coredump file write failed.fclose returned -1
03/06/16-01:16:58 (GMT) (tRAID): NOTE: QLProcessSystemError: Restart RISC
03/06/16-01:16:58 (GMT) (tRAID): ERROR: QLGetFwState: MBOX_CMD_GET_FW_STATE failed. Stat f000
03/06/16-01:16:58 (GMT) (tRAID): NOTE: QLRebootTimer: Status after Get FW State 4543
03/06/16-01:16:58 (GMT) (tRAID): NOTE: QLRebootTimer: QLGetFwState failed
03/06/16-01:16:59 (GMT) (tRAID): NOTE: QLStartFw: Downloading Driver's FW image 03.00.01.47 from 031fb740 4c0c8 bytes , result 0
03/06/16-01:17:26 (GMT) (tRAID): WARN: QLMailboxCommand: Cmd = 0069, completion timeout
03/06/16-01:17:26 (GMT) (tRAID): WARN: QLMailboxCommand: command completion timeout, cmd = 0x69
03/06/16-01:17:27 (GMT) (tRAID): NOTE: Qlogic coredump file written to '9J6GTL1:/tmp/QLogic_Coredump_port_0_9J6GTL1',rc 204E50, expected 204E50
03/06/16-01:17:27 (GMT) (tRAID): WARN: Qlogic coredump file write failed.fclose returned -1
03/06/16-01:17:27 (GMT) (tRAID): NOTE: QLProcessSystemError: Restart RISC
03/06/16-01:17:27 (GMT) (tRAID): ERROR: QLGetFwState: MBOX_CMD_GET_FW_STATE failed. Stat f000
03/06/16-01:17:27 (GMT) (tRAID): NOTE: QLRebootTimer: Status after Get FW State 4543
03/06/16-01:17:27 (GMT) (tRAID): NOTE: QLRebootTimer: QLGetFwState failed
03/06/16-01:17:28 (GMT) (tRAID): NOTE: QLStartFw: Downloading Driver's FW image 03.00.01.47 from 031fb740 4c0c8 bytes , result 0
03/06/16-01:17:55 (GMT) (tRAID): WARN: QLMailboxCommand: Cmd = 0069, completion timeout
03/06/16-01:17:55 (GMT) (tRAID): WARN: QLMailboxCommand: command completion timeout, cmd = 0x69
03/06/16-01:17:56 (GMT) (tRAID): NOTE: Qlogic coredump file written to '9J6GTL1:/tmp/QLogic_Coredump_port_0_9J6GTL1',rc 204E50, expected 204E50
03/06/16-01:17:56 (GMT) (tRAID): WARN: Qlogic coredump file write failed.fclose returned -1
03/06/16-01:17:56 (GMT) (tRAID): NOTE: QLProcessSystemError: Restart RISC
03/06/16-01:17:56 (GMT) (tRAID): ERROR: QLGetFwState: MBOX_CMD_GET_FW_STATE failed. Stat f000
03/06/16-01:17:56 (GMT) (tRAID): NOTE: QLRebootTimer: Status after Get FW State 4543
03/06/16-01:17:56 (GMT) (tRAID): NOTE: QLRebootTimer: QLGetFwState failed
03/06/16-01:17:57 (GMT) (tRAID): WARN: QLStartAdapter: ControllerErrorCount exceeds threshold.
03/06/16-01:17:57 (GMT) (tRAID): ERROR: QLInitializeDevice: QLStartAdapter failed
03/06/16-01:17:57 (GMT) (tRAID): ERROR: QLAddDevice: controller/device/chip initialization failed.
03/06/16-01:17:57 (GMT) (tRAID): ERROR: qlgEnableHostInterface: QLInitializeDevice failed.
03/06/16-01:17:57 (GMT) (tRAID): NOTE: ********************************************************************************
03/06/16-01:17:57 (GMT) (tRAID): NOTE: QLogic Target Applicat
-=<###>=-
#--- Controller 0 Serial Output END-------------------------------------------------
Controller 1 Serial Output has been attached as a file. It seems to show that it has the dreaded Memory parity error.